Single-wire hoses have one layer of wire braid reinforcement, while double-wire hoses have two layers. Double-wire hoses can handle higher-pressure applications than single-wire hoses, making them ideal for more demanding environments. At the same size, double-wire hose is typically rated for roughly 1.5 to 1.8 times the pressure, in exchange for a stiffer, heavier hose with a larger bend radius. We carry a full range of single and double-wire hydraulic hoses to meet both light and heavy-duty requirements.
Both hose types are workhorses in mobile and industrial hydraulics, and choosing between them comes down to pressure, routing space, and cost. This guide breaks down how each one is built, how their pressure ratings compare by size, which standards apply, and when it makes sense to step up to 4 wire spiral hose instead.
How Single and Double Wire Hydraulic Hoses Are Built
Wire braid hydraulic hose has three layers:
- Inner tube: A synthetic rubber tube that carries the hydraulic fluid and is compatible with petroleum-based and many water-based fluids.
- Reinforcement: High-tensile steel wire braided around the tube to contain pressure. This is the only layer that differs between the two hose types.
- Outer cover: A synthetic rubber cover that protects the reinforcement from abrasion, oil, ozone, and weather.
Single wire braid hose uses one braided layer, which keeps it lighter, more flexible, and easier to route. Double wire braid hose adds a second braided layer, separated from the first by a thin rubber layer, which substantially increases its ability to contain pressure.
Single Wire vs Double Wire Pressure Ratings by Size
The difference is easiest to see side by side. The table below compares maximum working pressures for two Aeroquip braided hose lines sold by HSC: GH663 single wire (SAE 100R1AT) and GH793 double wire (SAE 100R2AT).
| Dash Size |
Hose ID |
Single Wire: Aeroquip GH663 (SAE 100R1AT) |
Double Wire: Aeroquip GH793 (SAE 100R2AT) |
Double / Single |
| -4 |
1/4 in. |
3,700 psi |
5,750 psi |
1.55x |
| -6 |
3/8 in. |
3,400 psi |
5,000 psi |
1.47x |
| -8 |
1/2 in. |
2,900 psi |
4,250 psi |
1.47x |
| -10 |
5/8 in. |
2,000 psi |
3,625 psi |
1.81x |
| -12 |
3/4 in. |
2,000 psi |
3,125 psi |
1.56x |
| -16 |
1 in. |
1,500 psi |
2,500 psi |
1.67x |
Source: HSC product listings for Aeroquip GH663 (SAE 100R1AT) and GH793 (SAE 100R2AT), accessed October 2026. Ratings vary by manufacturer and product line, so always confirm the rating printed on the hose layline.
Two patterns stand out. Double wire hose is rated for about 1.5 to 1.8 times the pressure of single wire hose at the same size, from 1.47 times at -6 and -8 to 1.81 times at -10. And for both types, the pressure rating drops as the hose diameter increases, so a larger hose needs more reinforcement to hold the same pressure.
SAE and EN Standards for Wire Braid Hose
Most wire braid hydraulic hose is built to SAE J517 (the 100R series) or the European EN standards. The most common designations include:
- SAE 100R1AT and EN 853 1SN: Single wire braid hose for medium-pressure service. Many hoses are dual-rated to both standards.
- SAE 100R2AT and EN 853 2SN: Double wire braid hose for high-pressure service, also commonly dual-rated.
- EN 857 1SC and 2SC: Compact single and double wire hose with a smaller outside diameter and tighter bend radius, useful where routing space is limited.
- SAE 100R16: Compact double wire braid hose with a tighter bend radius than standard 100R2AT.
- SAE 100R17: Constant-pressure hose rated for 3,000 psi across its size range. Smaller sizes use a single wire braid and larger sizes step up to a double braid to hold the same rating.
- SAE 100R5: Single wire braid hose with a textile cover, common on trucks and mobile equipment.
HSC stocks SAE 100R1AT, 100R2AT, 100R5, 100R16, and 100R17 hose, along with EN 857 compact hose, in its single and double wire braid category.
When to Choose Single Wire or Double Wire Hose
Choose single wire hose when:
- System pressure falls comfortably within the single wire rating for your hose size, including pressure spikes.
- The hose has to route through tight spaces where a smaller bend radius matters.
- Weight and flexibility are priorities, such as on lighter mobile equipment and agricultural implements.
- The line serves a lower-pressure function, such as return, pilot, or lubrication lines.
Choose double wire hose when:
- System pressure, or regular pressure spikes, exceeds what single wire hose is rated for at your size.
- The hose sits on a high-pressure circuit, such as the boom, arm, and bucket circuits on construction equipment or the main lines on an industrial press.
- You need extra margin for durability in demanding, continuous-duty applications.
Whichever you choose, the hose's maximum working pressure should meet or exceed the highest pressure the system produces, not just its normal operating pressure.
2 Wire vs 4 Wire Hydraulic Hose
When pressures or pressure spikes go beyond what double wire braid hose can handle, the next step is spiral hose. Instead of braided wire, 4 wire and 6 wire spiral hose uses layers of steel wire wound in alternating spirals, which handle higher pressures and far more pressure impulse cycles.
Common spiral hose standards include EN 856 4SP and 4SH and SAE 100R12, 100R13, and 100R15. Compared with 2 wire hose, 4 wire spiral hose:
- Handles higher working pressures, especially in larger sizes.
- Withstands more pressure impulse cycles, which extends service life on hard-working circuits.
- Is stiffer, heavier, and more expensive, with a larger bend radius.
Spiral hose is the standard choice for high-pressure, high-impulse circuits on excavators, mining equipment, and heavy industrial machinery. For most medium- to high-pressure lines, 2 wire braid hose remains the more practical and economical option.
Match Your Fittings to Your Hose
A hose assembly is only as strong as its weakest connection. Crimp fittings are engineered for specific hose series, and pairing a hose with a fitting that isn't specified for it can lower the assembly's rated pressure. Before replacing or upgrading a hose, confirm fitting compatibility using our guide on how to choose compatible hydraulic hose fittings, or let our team build it for you through our hydraulic hose assembly service.
Frequently Asked Questions
Is 2 wire hydraulic hose stronger than 1 wire?
Yes. At the same size, 2 wire (double wire braid) hose is rated for roughly 1.5 to 1.8 times the working pressure of 1 wire (single wire braid) hose. The tradeoff is less flexibility and a larger bend radius.
Can I replace a single wire hose with a double wire hose?
In most cases, yes, as long as the routing allows for the larger bend radius and the fittings are specified for the new hose series. Replacing a double wire hose with a single wire hose is only safe if the single wire hose is rated for the system's maximum pressure at that size.
What does R1 or R2 mean on a hydraulic hose?
R1 and R2 refer to SAE J517 hose types. SAE 100R1 is single wire braid hose and SAE 100R2 is double wire braid hose. The designation, size, and pressure rating are printed along the hose cover, called the layline.
How do I tell what type of hose I have?
Check the layline printed on the hose cover. It typically lists the manufacturer, hose series, SAE or EN standard, dash size, and maximum working pressure. If the layline is worn off, our team can help identify the hose.
Find Single and Double Wire Hydraulic Hose at HSC
Hydraulic Supply Company carries a full range of hydraulic hose, from single and double wire braid to 4 and 6 wire spiral, along with the fittings and protection sleeves to complete your assembly. For a broader overview of hose construction and ratings, see our guide to types of hydraulic hoses. Need help choosing? Contact our team or visit a branch location to talk with a hydraulic hose specialist.